Can An Infiniti Icc Laser Be Repaired?

ICC Sensor Alignment and Aiming

2013 Infiniti JX35 vehicles tin exist equipped with a new type of Intelligent Cruise Control (ICC) system. This system incorporates a new ICC Sensor which requires an essential service tool kit 1-20-2721-1-IF to perform aiming aligning service.

For the driver assistance systems to function properly, the new radar sensor must be precisely aligned using the ICC aligner. Nevertheless, if the ICC sensor is far out of adjustment, has been removed or a new part is installed; utilize the J-51093 ICC Sensor Alignment Tool to verify the radar unit is at least level before performing the ICC Sensor aiming adjustment procedure. The ICC sensor aiming process outputs millimeter radar waves then calculates the displacement adjustment in radar direction using CONSULT-Three plus Work Support.

Attach the J-51093 Sensor Alignment Tool to the ICC Sensor to ensure the sensor is level.

Preparation

ICC Sensor aiming is a simple procedure. If yous can align a vehicle, you tin can do the process!

Place the vehicle on a camera based Hunter wheel aligner machine.*

A four-bicycle vehicle alignment must always exist performed earlier proceeding with the ICC Sensor alignment and aiming process.

1. Adjust pressure in all tires to the specified cold tire pressure value.

ii. Empty the vehicle. (Remove any baggage from the rider compartment and cargo area.)

3. Shift the selector lever to "P" position, and release the parking brake.

4. Fully fill the fuel tank, and so bank check that the coolant and oils are filled up to correct level.

5. Clean off the fascia in front of the ICC Sensor.

Notation: The ICC Sensor is located behind the fascia then it should non r equire any cleaning. Whenever the sensor is removed or replaced, verify the crude level adjustment of the radar unit with the Sensor Alignment Tool earlier performing the ICC Sensor aiming process.

* IMPORTANT Annotation: The ICC Alignment Kit will office manually without a wheel aligner using a Hunter self-centering wheel adapter. Perform a 4-wheel alignment and then eye the steering wheel earlier offset the ICC Sensor alignment and aiming process.

Aiming Process

Positioning the Target Board

one. Visually position the center of the ICC target board approximately 3 feet in front end of the vehicle.

Annotation: The initial ICC target lath setting must be in the (vertical) position. Extend the tool concatenation from the target board to the ICC Sensor location. You tin employ the brass part of the chain to measure out approximately 3 feet.

Tech Tips: Employ the laser assembly to position and adjust the target board.

a. Place one side of the laser assembly flush against the center of the ICC target board mirror to aid in the positioning.

b. Turn the laser assembly ON allowing the laser axle to emit from the laser assembly toward the center of the ICC sensor.

c. Move the ICC target board as necessary so that middle of ICC target board aligns with heart of ICC sensor.

d. Conform the top of the ICC target board using the adjustable basics lifting or lowering to attain the proper height.

2. Align the mirror precisely to the vehicle thrust angle in a direct-alee position. This is accomplished by using the laser associates wheel-mounted adapter, stationary target and the target board.

three. Install Light amplification by stimulated emission of radiation Assembly

Install the wheel adapter on the right front wheel.
Mount the light amplification by stimulated emission of radiation associates to the cycle adapter as shown in the illustration.

4. Install Stationary Target Place the stationary target next to the correct rear wheel as shown in the illustration.

5. Target Lath Terminal Setting Extend the machined arm of the ICC target lath placing the reflective surface to the correct front side of the vehicle.

Turn the laser assembly ON. The front light amplification by stimulated emission of radiation signal (A) will be emitted toward the reflective surface on the target board arm and the rear laser point (B) volition be emitted toward the stationary target.

6. Confirm that the vehicle is pointing direct ahead and the ICC Sensor is level and aligned precisely with the target board, laser assembly and the stationary target.

a. Rotate or slowly pin the ICC target board stand to achieve the necessary horizontal aligning.

b. Adjust the ICC target board leveling screw to achieve the necessary vertical position aligning.

Note:

Horizontal aligning of the laser assembly can be assisted past slowly turning the steering cycle. Pivoting the entire stand up as necessary will also help to reflect the laser back to the laser associates..
Vertical aligning of the light amplification by stimulated emission of radiation assembly can exist assisted past rotating the leveling screw effectually its centrality until the two lasers meet.

Arrange the light amplification by stimulated emission of radiation beam every bit necessary until the two lasers match. Turn the laser assembly OFF when done.

vii. Employ CONSULT Work Support to Cheque and Adjust ICC Sensor Alignment.

Check displacement direction, and perform aligning every bit necessary. Perform the aligning determination for all iii different ICC target board positions. Follow all the instructions exactly every bit requested in CONSULT:

Position one, with 2° top tilted toward the vehicle.
Position 2, vertical.
Position iii, with 2° top tilted away from the vehicle.

Apply CONSULT To Check and Adjust Radar Alignment

1. Push ignition switch in the ON position.

2. Connect CONSULT and select "Light amplification by stimulated emission of radiation/RADAR," then "Work Back up."

3. Select "RADAR Alignment" and click Kickoff.

iv. Select "Radar Suit", and then "start" after the "RADAR Adjust" screen is displayed.

Notation: If an Fault Screen appears within approximately ten seconds afterwards "RADAR Adjust" is selected, the following causes are possible:

Radar Accommodate is selected, but the ICC target board is not installed in the correct position.
Adequate space is not secured effectually the ICC target board.
The radar alignment procedure exceeds its proper installation range.
- Deformation of vehicle body.
- Deformation of unit.
- Deformation of subclass.
The surface area is not suitable for the adjustment piece of work.
Right forepart side of fascia (ICC sensor view) or sensor is not clean.
The ICC system alert lamp illuminates.
The vehicle has low bombardment voltage
The extended arm and mirror is not stationary.

You will exist prompted with specific instructions to perform alignment of the sensor, (if necessary) by turning the sensor adjusting screw with the adjustment tool by a certain number of turns in increments of 0.25 in the direction indicated past CONSULT.

Exist careful not to cover the correct front side of the fascia (ICC Sensor view) with a hand or whatever other body part during adjustment, as this may result in incorrect radar adjust values.

half-dozen. CONSULT will not update the ADJ VALUE while you are turning the suit tool. Recheck the ADJ VALUE with CONSULT past performing the Radar Alignment steps after each incremental correction adjustment. Confirm proper radar alignment by following CONSULT steps until it shows "ADJ VALUE" to exist 0.00 turn. CONSULT will display a Completed message.

Annotation: Always perform the ICC system activeness test to confirm that the ICC organisation operates normally after replacing the ICC sensor or repairing whatever ICC arrangement malfunction.

Supersede the protective embrace during storage of the laser kit target board.

Table of Contents